Subs and amp hook up. How to Hook Up Subwoofers to an Amp

Subs and amp hook up Rating: 8,6/10 1646 reviews

How to Install Subwoofers: 14 Steps (with Pictures)

subs and amp hook up

They are just as much at home in an install meant for listening pleasure as it is in an all. Now your amp can power up and send the audio signals to the sub so all you need is some audio input for it. Incorrect installation of the subwoofer is securely fastened power, your subwoofer, an amplifier sends. Run the majority of the power cable through the hole in the firewall, making sure to leave enough wire to get to the battery. If there is just one blue wire, you can use that. Just turn the volume way down on whatever is sending the signal.

Next

What do i need to hook up my subs and amp

subs and amp hook up

Make sure both the subwoofer and the amplifier are turned off and disconnected from the power source. The example attached to this step wouldn't be sufficient with its pathetic 18 amp peak power. However the door-subwoofers and rear subwoofers are powered by. You will need to run the 16 - 18 gauge wire through the back of the center console too. This is a great forum and I have newfound respect for you audiofiles.

Next

ONE CHANNEL AMP AND TWO SUBS....NOW WHAT?

subs and amp hook up

Get all of the subs and amps you could possibly need by shopping from our. If your stereo does not have these connections, you will have to splice the wires into the rear speaker wires. Installing powerful subwoofers into an older vehicle puts a big strain upon the metal panels of the car, and the welds holding the panels together. Refer to instructions for your specific sub or preamplifier for questions on available adjustments. What if i have is connected the best friend. If I'm not mistaken, you can bypass the amp on the sub with a separate amp if hooked up through speaker level.

Next

How to hook up a car subwoofer to your computer or home theater system

subs and amp hook up

First: Is your Amp a 1 or 2 or 3 channel amp? The bigger ones also handle lower frequencies better too. Most modern power supplies can supply 20+ amps at 12 volts. This wire tells the amp that the stereo has turned on, and that the amp should too. See the next step for those details. The only thing you have to worry about is if it provides enough power for your particular amp. Wrap electrical tape around the end of the red wire and do not strip it. Stereo receivers, pre-amps, and integrated amplifiers rarely have.

Next

How to Install Subwoofers: 14 Steps (with Pictures)

subs and amp hook up

Cut all four wires with a scissors just before the white connector so it's just four bare wires. If so, how do I wire the one channel to the speakers so I that I don't blow anything up? You'll want to do it exactly like it was in your car. See the attached picture for an example of the correct connector. From what I have seen happen is that the subs work in 2 main ways that I know of. This is the metal wall under the hood of the car, closest to the windshield.

Next

Hook up subs amp

subs and amp hook up

One should never match amplifier power with speaker power. As for the black wire next to the red one, cut about two inches of that wire off and strip both ends to make a short with the red wire even less likely and also because you need a spare 2 inch wire later. See the attached image for an example. The good pratice is to pick a speaker rated for 170% of the amplifier power. It is important to get the power from the battery and not the fuse box. Once you've connected the car's audio in this can check out 500 watts of wiring do i connect my subwoofers. So at 12 volts it needs 25 amps to reach max power.

Next

How to Wire an Amp to a Sub and Head Unit: 12 Steps

subs and amp hook up

To do this, you'll need your subwoofer, an amplifier, at least one set of these are the red, white, and yellow jacks on a single cable , , and speaker wires. If it is a stock stereo on a car without a power antenna and no blue wire, then run the 16 - 18 gauge wire to the fuse box, and connect it to a fuse that turns on when the accessories are on. We will start with wiring the power from the battery. Walmart sells amplifier kits as do some other stores. Step by step instructions on how to hook up your new subwoofer to a church. Connect the 3 foot, 10 gauge wire to the one marked do not connect it to the speaker negative : B- Neg -12v Gnd Ground Connect the other end of the ground wire to a nearby bolt that connects to the body of the car.

Next

What do i need to hook up my subs and amp

subs and amp hook up

Without the easy ways to hook up will affect how to send tv in this. Make sure you tape the place where you wired the fuse to the wire, so you don't get a short. In this article We'll go deeper and set you up with a. What I have done is wired the speaker output, into the rear speakers. I've been preoccupied lately researching and have found many quality sites thanks to this forum. If you're bridging two channels, make sure they're bridged the same way. Yes, two easy ways to hookup a powered sub in a 2-channel setup.

Next

Installing Subwoofers in a Car: 8 Steps

subs and amp hook up

Then cover the end of the shorter black wire with electrical tape also. The problem is that the amps are different brands so to avoid powering. Now stick one end in the main power connector's green wire hole and stick the other end into any black wire's hole. Older power supplies tend to fail a lot and ebay sellers don't always list the max current ratings so if you want to be sure, get a cheap, brand new power supply from newegg. After that simple setup your amp will now turn on as soon as you plug the power supply in and switch it on. To wire two subwoofers to a mono amplifier, you need only know how to cut wire, hook up subs amp use.

Next