Hook up baseboard heater. Hooking up a baseboard heater

Hook up baseboard heater Rating: 9,9/10 141 reviews

Two baseboard heaters connected to one thermostat.

hook up baseboard heater

The quiet operation and space-saving designs that most baseboard heaters offer can also be an excellent selling feature for your home. They do the job that they were designed to do, but they have drawbacks. The heater may sit directly on any floor surface, including carpet. Place it either under a window, along an outside wall, or as close as possible to an outside door. The line connection will be attached to the feeder wires that come from the circuit breaker.

Next

How to Wire Electric Baseboard Heaters

hook up baseboard heater

The percentage of anti-freeze Propylene Glycol is determined by the type of heat source on-demand heater or tank-type and by the guidelines listed on the anti-freeze container. All of our heating units are manufactured to an industry standard of quality and reliability. Do not install heater beneath an electrical outlet. Remove the top of the cover off the center bracket and off the immediate supports. The 1 inch hole saw should be used for making a hole in the positions of these 2 pipes. Anyhow I followed the wiring diagram on heater and wired to a 2pole 15amp and I turned on breaker and it popped so I pulled apart the heater and looked it all over again.

Next

Two baseboard heaters connected to one thermostat.

hook up baseboard heater

You can use a stud finder to do this. We offer units that will heat both your Radiant space heating and domestic hot water. Before proceeding, you must decide whether you prefer 2000 or 2500 watts. If freeze protection is an issue, than a closed system with anti-freeze is a good idea. Install two screws through the cover into the junction boxes.

Next

How to Wire Electric Baseboard Heaters

hook up baseboard heater

If you have an outdoor wood boiler, and for whatever reason you need to use antifreeze in the radiant floor system, the following schematic should be very helpful. Attach the bare or green wire to the load ground wire. Follow installation instructions for mounting and wiring your baseboard heater and you're good to go! Step 2 - Turn Off the Electrical Power Go to the circuit breaker panel and turn off the breaker that feeds electricity to the baseboard heater. Verify that the electrical supply wires are the same voltage as the heater. Splice the other ends of the thermostat wires to the heating elements. In this case, you will need to install two separate 20-amp circuits for the heaters, because you can't safely draw more than 16 amps over 12-gauge cable.

Next

How to Install Baseboard Heating (Electric)

hook up baseboard heater

Click here for information on the. Be sure it is clear of all obstructions and that there is a 12 inch clearance between the heater and drapes. And since most boilers have water jackets containing several hundred gallons of water, 50% of the water in the boiler could be 185 degrees the temperature at which the boiler damper shuts off the air supply and sends the boiler into resting mode and the other 50% could be considerably cooler. The lower voltage across the two ends of a given heater means that the maximum temperature is lower than normal. Step 3 - Study the Manual Take the thermostat out of the package and check the instruction manual for reference.

Next

Should Your Heaters Be Wired in Parallel or in Series?

hook up baseboard heater

For example, if the heaters add up to 4,000 watts and you divide that by 240, you get just over 16 amps. Mark the location on the wall or floor for the power supply entry into the heater. If it is heating, the heater could be defective or the wiring is done incorrectly. Also, if you wire in series, the failure of one heater most likely affects the other heater. The entire package is pressure tested against leaks and as few as four solder connections can tie it into your system. If wiring on the right, disconnect factory connector B.

Next

How to Wire Your Baseboard Heater

hook up baseboard heater

Determine where you want to install the heater. Connecting the heaters in parallel means that essentially the two wires coming from the power source the thermostat go to the two ends of the first heater, and the same two wires then continue on and are connected to the two ends of the second heater as well. There is no connection whatsoever to the domestic water supply. Just remember to bury the supply and return lines from your boiler below the frost line. For 2500 watt applications: Connect the remaining supply wires to both the black and red wires. Connecting the heaters in series means that one of the wires from the power source the thermostat goes on one end of the first heater, the other end of that first heater is connected to one end of the second heater, and the last end is connected back to the power source.

Next

How to Install a Hot Water Baseboard Heater

hook up baseboard heater

. Radiant Floor Company can customize a Zone Manifold to suit any application. Radiant Floor Company includes this information on your worksheet. The load connection, on the other hand, will tie in with the wires for the heater. For standard baseboard wring on the right or left 120V or 240V supply.

Next

The Closed System

hook up baseboard heater

Multi-watt baseboard heater right or left wiring 120V or 240V supply. The same project after installing a design from us! Follow this link, for information on filling and purging your Closed Radiant heating system. Connect the bare ground wires to the grounding screw on the baseboard heater's metal frame. Mount the heater flush against the wall. Step 5: Input and Output Pipe The fifth step is to use a pencil to note the positioning of the input pipe and the output pipe.

Next

Should Your Heaters Be Wired in Parallel or in Series?

hook up baseboard heater

Go to the circuit breaker panel and switch the heater breaker on. Step 4: Aligning the Holes Place the heater such that the screw holes lie in the same plane as the wall studs. The people I bought the house from ran power to the first heater then from there to another. So, Why Choose One Way Over the Other? The main advantage to this system lies in the fact that, being closed, anti-freeze instead of water can be used as the heat transfer medium. Do not install heater against vinyl wallpaper, paperboard, or low density fiberboard surface.

Next